iSCSI configuration details for host connections

You must follow these configuration details for iSCSI host connections.

You can attach the system to Small Computer System Interface Over Internet Protocol (iSCSI) hosts by using the the systems.

Note: The system supports SAN devices that bridge iSCSI connections into a Fibre Channel network.
iSCSI connections route from hosts to the systems over the LAN. You must follow these configuration rules:
  • The system supports up to 1024 iSCSI sessions per node.
  • The system currently supports one iSCSI connection per session.

Nodes have two Ethernet ports. These ports are for 1 Gbps support.

Depending on the optional functions that are installed, the system supports a number of Fibre Channel and iSCSI connections at different connection speeds.

iSCSI hosts connect to the system through the node-port IP addresses, which can be assigned to any Ethernet port of the node. If the node fails, the address becomes unavailable and the host loses communication with the system via that node. To allow hosts to maintain access to data, the node-port IP addresses for the failed node are transferred to the partner node in the I/O group. The partner node handles requests for both its own node-port IP addresses and also for node-port IP addresses on the failed node. This process is known as node-port IP failover. In addition to node-port IP addresses, the iSCSI name and iSCSI alias for the failed node are also transferred to the partner node. After the failed node recovers, the node-port IP address and the iSCSI name and alias are returned to the original node.

Multiple configurations are supported if the following requirements are met:

A volume can be mapped the same way either to a Fibre Channel host, an iSCSI host, or both.

For the latest maximum configuration support information, search for Configuration Limits and Restrictions and your product name at the following website:

https://datacentersupport.lenovo.com/

The system supports the following I/O descriptions:
  • I/O from different initiators in the same host to the same I/O group
  • I/O from different initiators in different hosts to the same volumes
  • I/O from Fibre Channel and iSCSI initiators in different hosts to the same volumes
I/O from Fibre Channel and iSCSI initiators in the same hosts to the same volumes is not supported.

A clustered Ethernet port consists of one Ethernet port from each node in the clustered system that is connected to the same Ethernet switch. Ethernet configuration commands can be used for clustered Ethernet ports or node Ethernet ports. Systems can be configured with redundant Ethernet networks.

To assign an IP address to each node Ethernet port for iSCSI I/O, use the management GUI or the cfgportip command. The MTU parameter of the CLI command specifies the maximum transmission unit (MTU) to improve iSCSI performance.

You can configure iSNS to facilitate scalable configuration and management of iSCSI storage devices. Currently, you can have only one type of protocol that is used by the iSNS server at a time: either IPv4 or IPv6. For example, if you try to configure an IPv6 iSNS IP address when you already configured an IPv4 iSNS IP address, the new IPv6 IP address becomes the iSNS IP address. The old IP address can no longer be used for iSNS function.

iSCSI supports two types of authentication through the Challenge Handshake Authentication Protocol:
  1. One-way authentication: iSCSI target authenticating iSCSI initiators
  2. Two-way (mutual) authentication: iSCSI target authenticating iSCSI initiators, and vice versa.
Attention: With the iSCSI initiator, you can set two passwords: one for discovery and another for iSCSI session I/O. However, the system requires that both passwords for each type of authentication are the same. That is, two identical passwords for one-way CHAP, and two identical passwords for two-way CHAP that are different from those passwords for one-way CHAP.

You can map an iSCSI host to volumes that are accessible through multiple I/O groups. iSCSI hosts can access volumes that are accessible through multiple I/O groups (and single I/O groups). An iSCSI host that is mapped to a volume that is accessible through multiple I/O groups is online if it has at least one active iSCSI session with each I/O group of the access set. If volumes are not mapped to an iSCSI host, it is degraded. If a volume is mapped to an iSCSI host but there no active iSCSI sessions to any I/O group part of the volume access set, the host status is offline.

If an iSCSI host does not have a multipath driver that is installed and the host is mapped to a volume that is accessible through multiple I/O groups, the host status is always degraded. Only a single path between the host and system I/O groups is supported in such a scenario. This single path is true also for AIX, which does not have a multipath driver that supports iSCSI.

On Lenovo Storage V5030 and Lenovo Storage V5030F systems, iSCSI hosts that have a multipath driver that is installed can be moved nondisruptively. However, this capability does not include IBM AIX host attachment as it does not support multipath functions.

iSCSI attached hosts are supported by HyperSwap volumes. However, the HyperSwap function requires that the host multipath driver be configured to use an ALUA-based path policy. The HyperSwap function is not supported for AIX iSCSI hosts that do not have a multipath driver installed.

On Lenovo Storage V5030 and Lenovo Storage V5030F systems, iSCSI attached hosts are supported by HyperSwap volumes. However, the HyperSwap function requires that the host multipath driver be configured to use an ALUA-based path policy. The HyperSwap function is not supported for AIX iSCSI hosts that do not have a multipath driver installed.

iSCSI protocol limitations

When you use an iSCSI connection, you must consider the iSCSI protocol limitations:
  • There is no SLP support for discovery.
  • Header and data digest support is provided only if the initiator is configured to negotiate.
  • Only one connection per session is supported.
  • A maximum of 1024 iSCSI sessions per iSCSI target is supported.
  • Only ErrorRecoveryLevel 0 (session restart) is supported.
  • The behavior of a host that supports both Fibre Channel and iSCSI connections and accesses a single volume can be unpredictable and depends on the multi-pathing software.
  • A maximum of four sessions can come from one iSCSI initiator to an iSCSI target.
The following iSCSI session parameters are supported:
initial_r2t = 1
immediate_data = 0
max_connections = 1
Max_recv_segment_data_length = 32k
max_xmit_data_length = 32k
max_burst_length = 32k
first_burst_length = 32k
default_wait_time = 2
default_retain_time = 20
max_outstanding_r2t = 1
data_pdu_inorder = 1
data_sequence_inorder = 1
error_recovery_level = 0
header_digest = CRC32C,None
data_digest = CRC32C,None
ofmarker = 0
ifmarker = 0
ofmarkint = 2048
ifmarkint = 2048